#Charter arms pathfinder plus#

This wheelgun, introduced in 1973, was designed to be a big-bore concealment piece, and it quickly became very popular. One of Charter ArmsвЂ™ most well known revolvers is the Bulldog in. RELATED STORY: Charter ArmsвЂ™ New Pitbull Revolver in. This was basically the same gun as the Undercover, but it had a six-shot cylinder bored to take the. To capture some of that market, Charter Arms introduced the Undercoverette. Back in the day, some police departments issued female officers revolvers chambered for the milder-shooting. 38 Special loads, it rode in an ankle holster on my left leg. I had an Undercover that I bought in the mid-1970s, and as I recall the fit and finish was on par with a square-butt Chief that I also owned at the time. Quality-wise, the Charter was right up there with other American handgun makers. Fifty years ago, a $10 savings could make a big difference. In the 1965 edition of Gun Digest, S&WвЂ™s Chief Special was listed at $65, a Colt Detective Special was $69.50 and the Charter Arms Undercover was quoted as $55. The Undercover was also made available with a nickel finish and a 3-inch barrel as time went on. Initially, the Undercover was sold with a polished blue finish and smooth walnut grips that held a silver Charter Arms medallion. Finally, the machined barrel had eight-groove rifling instead of six-groove, which improved the bullet seal and resulted in higher velocities and better accuracy potential. It was also the only American revolver that didnвЂ™t have a cylinder stop in the frame to hold the cylinder in place when it was open for loading.

The cylinder locked in three different places instead of just two-at the breech face and on both sides of the frame using the ejector rod collar. The Undercover also used a hammer-block, transfer-bar safety system invented by Charter that only allowed the gun to fire when the trigger was fully to the rear.

RELATED STORY: Swamp King вЂ“ The Charter Arms Gator Revolver Both the trigger and the hammer spur were wider for easier user manipulation.

#Charter arms pathfinder plus#

The action itself had fewer major moving parts than its competitors, plus it had a shorter hammer throw, making the lock time faster. It was spring-loaded and made of tough beryllium copper, making it almost unbreakable. Charter Arms, however, fitted the firing pin of the Undercover in the frame. 38 Special UndercoverД¬olt and S&W centerfire revolvers at the time had their firing pins riveted in the hammer nose. By comparison, the S&W ChiefвЂ™s Special weighed 19 ounces and was roughly the same size.Д«etter Backup Charter Arms. The grip frame/triggerguard was a one-piece unit made of aluminum alloy, which kept the weight of the gun down to 16 ounces and which permitted Charter Arms to advertise it as the lightest steel-framed revolver on the market.

All internal parts were attached by screws or pins, plus all the springs were coil springs. Unlike conventional revolvers, there was no sideplate access to the action was through the bottom of the frame. It was conceived by American engineers who wanted a new and different handgun design while keeping with the traditions established in New EnglandвЂ™s вЂњGun Valley.вЂќ At the time, this revolver was very different from the wheelguns produced by Colt and Smith & Wesson.ДЇor starters, the frame was a solid piece of steel, which provided added strength. The very first Charter Arms product was a five-shot, double-action, snub-nose revolver in. Your lady friend may in fact be more comfortable with the smaller Undercover walnut grips.ДЄlthough Charters are not as well regarded as (say) a S&W or a Ruger, at the Charter's much lower price point, the value received (bang for your bucks) is hard to beat.Charter Arms has been around since 1964. If you acquire a stainless model, I will tell you that the sights are hard to distinguish from the barrel, as they are the same color - which I remedied with a dollop of Ithernational Orange on the front sight blade's top and a white line around the sides/bottom of the rear sight notch (both are model paint).ДЄlso, the Pathfinder grip frames are the same as every other Charter DA revolver regardless of caliber, which means the the issue rubber bumpers on the newer guns can be switched out for the walnut grips of older/other models ( I installed the square butt target grips on my stainless CA - the 1970's CA was issued with walnut carry grips). They are good Trail Guns for close ranges shooting, but despite the factory model name, are not accurate enough to be a target pistol. I bought the 1970's CA used, and the 2008 CA new/ordered - and have had zero issues with either. 22 Mag-only 3' Pathfinder and a 2008 Target Pathfinder 4' Dual Cylinder (LR/WRM) Model.